How to make a two channel wireless robot at your home

By -






Easy steps to make a wireless robot

 Here comes with the next level of my recent post,make your own wireless robot which can move forward,backward and left ,right.
You will need some components which are easily available at hobbyking.com.

 Now comming to the tools...
Tools we need

1. Soldering iron
2. Wire cutter
3. One sided tape
4. Plier
5. Screw driver
6. Glue gun (not really necessary)
7. Double sided tape
Components we need

1. 12V DC motors *2
2. Chassis *1
3. Wheels *4
4. Rainbow wire(only for connecction)
5. Dpdt box*1
6. Dpdt switches*2
7. 12V battery
8. 9V battery
9. Relay circuit board
10. Wireless receiver
11. Wireless sender
12. Battery connector 
13. Double sided foam tape
14. Dead axel
Steps to be followed
Step-1

Assemble all the motors on the chassis and connect the motors as shown in the figure.

Assemble two wheels with the help of dead axle insted of using castro wheel.

Step-2

Now connect the dpdt switches with the wire with the sender.Then put the dpdt(s) on the dpdt box as well as the sender.





 Step-3
Now coming to the bot.After assembling all the motors and connect the motor1 and motor2 with the relay circuit board.

Step-4
Its time to connect the relay circuit board and the receiver.Connect the signal wires and power plug as shown in the figure. 


Step-5
Now mount both the relay circuit board and the receiver on to the bot by the help of double sided foam tape as shown in the figure. 

Step-6
Now mount the battery on the bot by applying double sided foam tape and connect the battery to the receiver by the help of battery connector. 



Step-7
After that power up the remote by connecting 9V DC battery.Here is the battery connecting point of the sender.Solder 9V battery connector on it and connect it to the battery.




Step-8
Set both the receiver and sender decoder at same numeric digits.Push the little button up side to set the numeric digits.




Step-5
I add a LED board(NEON 2.0) to make it more attractive.


Comments

Post a Comment

Popular posts from this blog

How to make a simple line following robot using Arduino uno

By -
Image
Line following robot In this tutorial I am gonna show you how to make a simple line following robot using IR sensors and ARDUINO UNO.I will be providing very easy and effective code that will help you to solve maze containing 90°,45° angles and curves.So les get started. Components required: 1.Arduino uno board 2.L293D motor driver IC 3.IR sensors(here i am using 5 sensors for the perfection of the robot) 4.Chassis 5.BO motors(two) 6.Castro wheel(one) 7.Batteries 8.Power bank(to power the ARDUINO) Steps to be followed:                             Step-1 Assemble BO motors and Castro wheel on the chassis as shown in the figure. Note: This is an example,my real robot have hand made chassis but the process is same. Step-2 Now place the battery and the Arduino uno board on the top of the chassis as shown.Connect the two batteries in series to get 8V out put. Step-3 Connect th...
Read more

How to make a simple obstacle avoiding robot using Arduino uno

By -
Image
Obstacle avoiding robot Its a kind of automatic robot which can avoid obstacles coming in front its path.In this tutorial I am gonna show you how to make it using simple components and using super simple code. Components we need : Arduino uno R3 *1 Ultrasonic sensor *1 150 RPM BO motors *2 Motor driver IC (L293D) Wheels*2 4V rechargable battery *2 Power bank( any mAh specification )*1 Jumper wires chassis*1 Steps to be followed : Step-1 Assemble BO motors and Castro wheel on the chassis as shown in the figure. Note: This is an example,my real robot have hand made chassis but the process is same. Step-2 Now place the battery and the Arduino uno board on the top of the chassis as shown.Connect the two batteries in series to get 8V out put. Step-3 Connect the motors and power source to the L293D IC as shown in the figure The polarity of the motors can be changed by altering the pin no. jack if the motor does not spin in t...
Read more