How to make simple wired remote control robot

By -



DIY Remote Control Robot

 In this tutorial i am gonna show you how to make a simple remote control robot. Its damn easy and consume hardly 2 hours to complete the entire task,

 Tools we need

1. Soldering iron
2. Wire cutter
3. One sided tape
4. Plier
5. Screw driver

 Components we need

 1. 12V DC motors *4
2. Chassis *1
3. Wheels *1
4. Rainbow wire
5. Dpdt box*1
6. Dpdt switches*2
7. 12V battery

 Steps to be followed
Step-1

Assemble all the 4 motors on the chassis and connect the motors as shown in the figure.
let right side motor be motor 1 and left side be motor 2

Step-2

Now solder wires on the dpdt switches as shown


A,B and C,D will be connect to the motor pair 1 and 2 respectively 

Step-3

Now put the dpdt switches on to the dpdt box as shown in the photo 

Step-4

Now connect all the wire according to their terminals.

Step-5




Now assemble the wheels on the motor.
Step-6

Your final model will some how look like this
Middle dpdt switch is for extra motor,You dont need to add that.



 Step-7
Now power up your bot by connecting the wire of the dpdt to the battery and you are ready to bang..!!!!!

Comments

Post a Comment

Popular posts from this blog

How to make a simple line following robot using Arduino uno

By -
Image
Line following robot In this tutorial I am gonna show you how to make a simple line following robot using IR sensors and ARDUINO UNO.I will be providing very easy and effective code that will help you to solve maze containing 90°,45° angles and curves.So les get started. Components required: 1.Arduino uno board 2.L293D motor driver IC 3.IR sensors(here i am using 5 sensors for the perfection of the robot) 4.Chassis 5.BO motors(two) 6.Castro wheel(one) 7.Batteries 8.Power bank(to power the ARDUINO) Steps to be followed:                             Step-1 Assemble BO motors and Castro wheel on the chassis as shown in the figure. Note: This is an example,my real robot have hand made chassis but the process is same. Step-2 Now place the battery and the Arduino uno board on the top of the chassis as shown.Connect the two batteries in series to get 8V out put. Step-3 Connect th...
Read more

How to make a simple obstacle avoiding robot using Arduino uno

By -
Image
Obstacle avoiding robot Its a kind of automatic robot which can avoid obstacles coming in front its path.In this tutorial I am gonna show you how to make it using simple components and using super simple code. Components we need : Arduino uno R3 *1 Ultrasonic sensor *1 150 RPM BO motors *2 Motor driver IC (L293D) Wheels*2 4V rechargable battery *2 Power bank( any mAh specification )*1 Jumper wires chassis*1 Steps to be followed : Step-1 Assemble BO motors and Castro wheel on the chassis as shown in the figure. Note: This is an example,my real robot have hand made chassis but the process is same. Step-2 Now place the battery and the Arduino uno board on the top of the chassis as shown.Connect the two batteries in series to get 8V out put. Step-3 Connect the motors and power source to the L293D IC as shown in the figure The polarity of the motors can be changed by altering the pin no. jack if the motor does not spin in t...
Read more

How to make a two channel wireless robot at your home

By -
Image
Easy steps to make a wireless robot Here comes with the next level of my recent post,make your own wireless robot which can move forward,backward and left ,right. You will need some components which are easily available at hobbyking.com. Now comming to the tools... Tools we need 1. Soldering iron 2. Wire cutter 3. One sided tape 4. Plier 5. Screw driver 6. Glue gun (not really necessary) 7. Double sided tape Components we need 1. 12V DC motors *2 2. Chassis *1 3. Wheels *4 4. Rainbow wire(only for connecction) 5. Dpdt box*1 6. Dpdt switches*2 7. 12V battery 8. 9V battery 9. Relay circuit board 10. Wireless receiver 11. Wireless sender 12. Battery connector  13. Double sided foam tape 14. Dead axel Steps to be followed Step-1 Assemble all the motors on the chassis and connect the motors as shown in the figure. Assemble two wheels with the help of dead axle insted of using castro wheel. Step-2 Now con...
Read more