Then we didn't stop : NIT Rourkela

By -



Then we didn't stop:
 After coming back from our first fest,we came with a huge potential,with a dream to achieve something.Luckily we got a new project to do in NIT Rourkela's techfest.

Our task:
All we had to make a simple forward-backward and side by side moving simple robot.But this should be WIRELESS.The bot we named was "NEON 2.0" after the name of the event "Robo-venture 2.0". Robo-venture 2.0 had the participants guide a self-built wireless user controlled robot through a maze where it had to cross specific checkpoints, while facing various obstacles,in the minimum time to win the game.
Real image oof the maze
Our robot(NEON 2.0):
As i said before,we had to make a wireless robot using Tx,Rx system. Aready i have uploaded the tutorial on "How to make a two channel wireless robot at your home".Click the link below to go to the page directly
how-to-make-two-channel-wireless-robot.

 Conclusion:

  The team who won the competition by completing the maze in a record of 8 minutes. And to the top it all, the team, which was from VSSUT. However, the runner-ups position was tied up between 2 teams – C.V.Raman College of Engineering,Bhubaneswar(which is our college) and CET, Bhubaneswar. The time taken to complete the task for one team was 10 min 34 sec 58 milliseconds and by another one was 10 min 34 sec 60 milliseconds. As there was just a difference of a fraction of microseconds between them, it was decided to let both teams have the runners-up position.


















Comments

Post a Comment

Popular posts from this blog

How to make a simple line following robot using Arduino uno

By -
Image
Line following robot In this tutorial I am gonna show you how to make a simple line following robot using IR sensors and ARDUINO UNO.I will be providing very easy and effective code that will help you to solve maze containing 90°,45° angles and curves.So les get started. Components required: 1.Arduino uno board 2.L293D motor driver IC 3.IR sensors(here i am using 5 sensors for the perfection of the robot) 4.Chassis 5.BO motors(two) 6.Castro wheel(one) 7.Batteries 8.Power bank(to power the ARDUINO) Steps to be followed:                             Step-1 Assemble BO motors and Castro wheel on the chassis as shown in the figure. Note: This is an example,my real robot have hand made chassis but the process is same. Step-2 Now place the battery and the Arduino uno board on the top of the chassis as shown.Connect the two batteries in series to get 8V out put. Step-3 Connect th...
Read more

How to make a simple obstacle avoiding robot using Arduino uno

By -
Image
Obstacle avoiding robot Its a kind of automatic robot which can avoid obstacles coming in front its path.In this tutorial I am gonna show you how to make it using simple components and using super simple code. Components we need : Arduino uno R3 *1 Ultrasonic sensor *1 150 RPM BO motors *2 Motor driver IC (L293D) Wheels*2 4V rechargable battery *2 Power bank( any mAh specification )*1 Jumper wires chassis*1 Steps to be followed : Step-1 Assemble BO motors and Castro wheel on the chassis as shown in the figure. Note: This is an example,my real robot have hand made chassis but the process is same. Step-2 Now place the battery and the Arduino uno board on the top of the chassis as shown.Connect the two batteries in series to get 8V out put. Step-3 Connect the motors and power source to the L293D IC as shown in the figure The polarity of the motors can be changed by altering the pin no. jack if the motor does not spin in t...
Read more

How to make a two channel wireless robot at your home

By -
Image
Easy steps to make a wireless robot Here comes with the next level of my recent post,make your own wireless robot which can move forward,backward and left ,right. You will need some components which are easily available at hobbyking.com. Now comming to the tools... Tools we need 1. Soldering iron 2. Wire cutter 3. One sided tape 4. Plier 5. Screw driver 6. Glue gun (not really necessary) 7. Double sided tape Components we need 1. 12V DC motors *2 2. Chassis *1 3. Wheels *4 4. Rainbow wire(only for connecction) 5. Dpdt box*1 6. Dpdt switches*2 7. 12V battery 8. 9V battery 9. Relay circuit board 10. Wireless receiver 11. Wireless sender 12. Battery connector  13. Double sided foam tape 14. Dead axel Steps to be followed Step-1 Assemble all the motors on the chassis and connect the motors as shown in the figure. Assemble two wheels with the help of dead axle insted of using castro wheel. Step-2 Now con...
Read more